Specifications

Description

Detailed Product Description
Macallister carbon brush,carbon brush for power tools,carbon brush replacement.
1. long service life
2. small spark, low noise

Macallister carbon brush, Macallister carbon brush for power tools, carbon brush replacement

1. long use life

2. small spark, low noise

3. anti-electrical interference

4. excellent performance

Macallister carbon brush, Macallister carbon brush for power tools, carbon brush replacement

Sizecustomized
Code No.

No

For ModelsMACALLISTER COD1500TSS

power tools carbon brush

we can supply various kinds of power tools carbon brushes,our carbon brushes have characteristics such as long service life, low noise, small spark and excellent performance.

Our products manufactured by automatic carbon brush machines bear characteristics as follows:


1. From the perspective of appearance:

chamfer decent product, appropriate structure, standard specifications, the wire’s cross-section and length, not loose, falling off, broken off side, off angle, clamp and so on.


2. In terms of function and use:
(1) Graphite products using high-quality, long life and do not wear commutator or slip rings, commutator never appears  scratch, rough, ablation and so on.
(2) With a good flow properties and set to change commutation , so that spark suppression in the permitted range, and the energy loss is small.
(3) When carbon brush runs, no heat, noise, broken, what’s more never change color carbon brush‘s body, no ablation.
(4) During the running, It can make the surface of commutator or collector ring quickly form a uniform, moderate and stable oxide film.

Non-standard brush can be designed and be manufactured per buyer's drawing or sample.

Information for your reference

carbon brush performance

Commutator:
Unit must be in good condition, with less than .002" out-of-roundness. Bar edge must be chamfered and there should be no burned edges.

Brush Holders:
They must be mechanically sound and permit the brush to slide freely. Brush holder fingers must move freely and if the unit consists of constant pressure springs, these springs must be in good condition. Springs that are difficult to move, have an excessive accumulation of carbon, or are worn, will cause excessive brush wear.

Brush Holder Angles:
The angles should be set to the original manufacturer's specification. Any more than a 2 degree variation in the setting can cause arcing, bar burning, and excessive wear. Brush holders that vary in the angle set to the commutator will cause the unit to be "off neutral".

Brush Holder Spring Tension:
Maintaining the proper spring pressure reduces arcing, brush wear, heating, and commutator wear. Light spring tension can cause threading and definitely will shorten the brush life. As a general rule, we recommend that the brushes be set at 4 psi pressure. To calculate the pressure, measure the width and thickness of the contact face and calculate as follows:

Pressure in Pounds/Brush = (Width x Thickness x 4 psi)

Brush Holder Quartering:
To insure that the best machine electrical neutral can be achieved, the brush holders must be quartered. Quartering is setting the brush holders at equal distance around the commutator. For a 4 pole machine, the spacing will be every 90 degrees. If the quartering is not properly set, you may experience excessive arcing, heating, brush wear, and commutator wear.

Machine Neutral:
To obtain optimum machine performance, the brush must be set at the machine electrical neutral. If the unit is off neutral, you may observe sparking under a no-load condition. Depending upon how far off neutral the machine is set, there may be arcing and bar burning.

Carbon Brushes Description

 

The Principal Dimensions of a Carbon Brush

 

Note: 
 
We work to NEMA and ANSI tolerances on the dimensions given to us. Width and thickness dimensions should be established accurately. If in doubt, it should be noted that the internal dimensions of the brush holder should be about .003" greater than the nominal dimensions of the brush.

 

 

Flexible length is the length from the top of the longest side of the brush to the center of the terminal hole.

The dimensions of "d" on the double shank terminals may vary with the flexible size, reducing as the flexible size increases and the minimum permissible dimension should be stated.

Terminals:
Please give the size of opening.

 

 


Terms

FOB Price: US $ 0.01-1/ Pair
Minimum Order: 2000 Pair/Pairs
Port: Shanghai
Payment Terms: L/C,T/T,Western Union

Bruce Z's Products

You can verify Bruce Z using your contacts and professional networks..

Recently Viewed Products
Key Tags
46 Suppliers & 170 Products
Hot Air Oven
17 Suppliers & 64 Products
3 Wheel Motorcycle
18 Suppliers & 68 Products
PU Belt
95 Suppliers & 653 Products
Weaving Loom
21 Suppliers & 151 Products
Popular Products on Tradesparq
Dental Autoclave
36 Suppliers & 120 Products
Iron Garden Furniture
21 Suppliers & 78 Products
Clear Glass
30 Suppliers & 187 Products
Classical V Belt
6 Suppliers & 36 Products
Box Camera
113 Suppliers & 355 Products

How Tradesparq Works:

* Double-click video screen for full-screen.